Electrical Leak Location and Geomembrane Detection

Introduction

A geomembrane can look perfect and still leak. A pencil-tip hole under cover soil, a split seam, or a gouge from a bulldozer won't show from the berm.

On the Columbus Upground Reservoir in Ohio, Geosynthetics Magazine reported 69 leaks across 589 surveyed acres, many from construction damage.

Electrical leak location (ELL) finds these defects without tearing the liner apart. This guide is for pond owners, farms and ranches, contractors, municipalities, environmental managers, and industrial operators.

It covers how ELL works, how to pick a method, what a survey involves, where it fails, what it costs, and how to verify repairs.

Key Takeaways

  • ELL passes current around an insulating liner and locates leaks where the circuit completes.
  • Method choice depends on whether the liner is exposed, water-filled, covered, or double-lined.
  • A proper survey ends with repair and a follow-up check, not the first flagged spot.
  • Subgrade, seams, and protection layers decide how many defects you'll have to find.

What Is Electrical Leak Location (ELL) for Geomembranes?

A geomembrane is a flexible, low-permeability barrier that contains water, wastewater, agricultural liquids, industrial fluids, or waste. ELL finds individual defects in that barrier. It does not measure an overall leakage rate.

How the electrical circuit reveals a defect

An intact, nonconductive liner blocks current. Under ASTM D6747-25, voltage applied across a sufficiently insulating liner allows current passing through a hole to be located. Defects include punctures, tears, knife cuts, seam defects, and cracks.

Technicians scan the prepared area, watch for changes in potential or current, and mark each anomaly for repair.

Why ELL complements visual inspection

Eyes miss a lot. In Columbus, defects ranged from pencil-tip holes to seam splits and equipment damage several feet long, and the survey worked through cover soil. Covered wrinkles, seams, penetrations, and small punctures cannot be judged reliably by sight.

ELL is non-destructive when the system suits the method. It locates likely discontinuities. It doesn't replace engineering judgment, repair inspection, or regulatory documentation. It also doesn't verify seam strength; that takes separate seam testing.

Factors that affect whether ELL will work

  • Liner material that actually insulates
  • Moisture and a continuous conductive path above and below the liner
  • Subgrade conductivity
  • Grounding and perimeter isolation
  • Access to the test surface

GCLs and compacted clay liners without a polymeric geomembrane need a different evaluation approach. Check the chosen method against the current ASTM standard and project specifications.

Choosing the Right Electrical Leak Location Method

ASTM D6747-25 guides selection among exposed, water-covered, and earth-covered surveys. Start by naming the installed condition.

Exposed liner methods

  • Water puddle (D7002-22): Uses conductive water on a limited area of exposed liner.
  • Water lance (D7703-22): Scans a water stream over the exposed surface so the pond does not need to be filled.
  • Arc testing (D7953-20): Works on clean, dry surfaces with less water, but needs proper isolation.
  • Spark testing (D7240-25): Applies to conductive-backed geomembranes.

Water-filled or in-service containment

Water surveys run after filling, either by wading or from a boat or platform. ASTM D7007-24 says leaks as small as 1 mm are routinely found in water-covered surveys under favorable conditions. That is not a universal minimum hole size.

Before choosing this route, weigh:

  • Water supply and depth
  • Site access and safety
  • Whether you can drain the pond for repairs

Covered or backfilled geomembranes

Soil surveys can find damage from backfilling. They may need an electrical break between the backfill and surrounding ground. Future access matters too: anchor trenches, perimeters, and other details determine whether you can retest a covered liner.

Double-lined and composite systems

A secondary liner can electrically isolate the primary. Surveys may need conductive drainage layers, conductive geotextiles (ASTM D7852-23), or interstitial water. Such a system must be designed for the detection method. It is not universally testable.

Four geomembrane electrical leak location methods by installed condition

Questions to ask before selecting a method

  • What is the liner material?
  • Is it exposed or covered?
  • Is it single- or double-lined?
  • Is the subgrade conductive?
  • Is water available?
  • Can conductive structures be isolated?
  • What operating restrictions apply?
  • What documentation does the owner or regulator require?

How a Professional Geomembrane Leak Detection Survey Works

Pre-survey preparation

The team reviews drawings, material specs, seam layouts, anchor trenches, penetrations, drainage layers, prior inspections, and leak symptoms. On site, preparation means:

  • Cleaning the surface
  • Managing water levels
  • Confirming safe access
  • Isolating conductive structures
  • Ensuring electrical contact

At Columbus, dry cover had to be rewetted and perimeter isolation trenches needed pumping after rain.

Scanning and locating anomalies

Technicians split the area into manageable zones, scan systematically, and mark each suspect spot so repairs avoid needless excavation. Concrete, exposed metal, pipe penetrations, batten bars, and poor grounding can cause false positives. ASTM D7007 names metal pipe penetrations, pump grounds, and batten strips on concrete as items to isolate.

Confirming and documenting the finding

A definite, repeatable indication counts as a leak under D7007. Rescan or confirm signals before classifying them. The report should include:

  • Survey method and area tested
  • Liner and site conditions
  • Limitations and untested areas
  • Defect maps or coordinates
  • Photographs and applicable standards

Repair and verification

Repair work follows a clear sequence:

  1. Isolate the containment and expose the area if needed
  2. Make a qualified patch or seam repair
  3. Inspect the repair and retest the area

Three-step geomembrane leak repair and verification process

At Columbus, larger leaks masked smaller ones, and resurveys after repair found more defects.

A Geosynthetics Magazine case shows the stakes. A landfill repaired two holes with no change in leakage because wrinkles broke electrical contact.

After flooding the layers, the next survey found six pinholes and a roughly 3/16-inch hole. Leakage then fell below 5 gallons/acre/day. A final report should map defect locations and confirm whether repairs passed.

Warning Signs, Limitations, and Immediate Next Steps

How to investigate a suspected pond leak

Water loss has many causes: liner damage, evaporation, overflow, plumbing, groundwater, structural cracks, or operational changes.

Clemson Extension suggests comparing pond level change with a bucket of water. Similar drops point to evaporation; faster pond loss points to leakage. A rusted outlet pipe is another common culprit.

Document water levels first. Then look for:

  • Wet areas outside the containment
  • Erosion or seepage
  • Unusual vegetation
  • Sediment movement
  • Persistent loss after weather is accounted for

These signs can confirm leakage is likely, but they do not pinpoint the defect.

When ELL may be unsuitable or inconclusive

  • Dry or nonconductive subgrades
  • Conductive materials near the survey area
  • Inaccessible surfaces
  • Double liners without a designed conductive path
  • Standing obstructions or unsafe conditions

A qualified specialist should select the method and disclose coverage limits. Not every liner can be surveyed the same way. ASTM also flags high-voltage hazards and calls for experienced personnel.

What to do before testing

  • Keep operating records
  • Don't cover or disturb the suspect area
  • Gather liner and installation documents
  • Identify hazardous contents
  • Coordinate access and safety with the tester

Cost, Prevention, and Choosing a Liner Partner

What determines the cost of leak detection

There's no universal price. Cost drivers include:

  • Containment area and liner configuration
  • Exposed or covered condition
  • Access and surface conditions
  • Water supply and handling
  • Number of survey zones
  • Travel, reporting, and repairs

Ask for an itemized quote separating survey, mobilization, water handling, mapping, repairs, retesting, and engineering or regulatory documentation.

Design and installation choices that reduce future leakage risk

NRCS Code 521 requires a smooth, unyielding subgrade free of sharp stones, with no standing water, mud, or vegetation at placement. Where cushioning is needed, it specifies nonwoven geotextile of 10 oz/sq yd or heavier, or at least 6 in of suitable soil.

Other controls:

  • Prefabricated pipe boots at penetrations
  • Properly sized anchor trenches
  • Controlled seaming and quality control
  • Exposed testing before cover goes on

Design new systems with testing in mind, such as conductive layers or access details.

Geomembrane design choices that reduce future leakage risk

Working with a liner manufacturer and installer

Western Environmental Liner, an Arizona-based manufacturer, makes custom factory-fabricated geomembrane panels up to 300' x 300', with one-piece liners up to 150,000 square feet. Factory-welded panels reduce field-weld risk.

As an IAGI-certified installer, the company offers technical support on slopes, anchoring, and subgrade preparation, plus turnkey installation across the United States.

Its subgrade guidance calls for a flat, smooth, dry surface, 6 inches of compacted bedding where needed, and 4 to 12 inches of backfill depending on wildlife traffic. Earthwork itself is outside its scope.

If you're planning a new, replacement, or repair-related containment project, request a free quote.

Frequently Asked Questions

How can I identify a leak in my pond?

Track water levels and rule out evaporation and plumbing. Look for seepage or wet areas. Then use professional ELL testing to pinpoint the geomembrane defect.

What is the average cost of leak detection?

No dependable average exists. Area, access, liner design, method, water needs, reporting, travel, and repairs all shape the quote.

Can electrical leak location testing be performed on a covered geomembrane?

Often yes. ASTM D7007-24 covers water- and earth-covered liners. Feasibility depends on the cover, electrical pathway, perimeter details, and system design.

Is electrical leak location testing the same as a visual inspection?

No. Visual inspection checks surface condition; ELL tests electrical integrity across the sheet. They work best together.

How accurate is electrical leak location testing?

It depends on method, site preparation, liner configuration, equipment, operator skill, and conductive interference. Treat any single accuracy figure with suspicion.

What should I do after a leak is located?

Manage the contents safely, have qualified crews repair it, document the work, and inspect the patch or seam. Retest before returning the system to service.